输送树脂泵用NYP50转子泵填料密封

 ●高粘度泵优点：

　　转子泵的轴向位置可调，不需要拆泵。

　　泵采用模块化设计，可根据不同的使用要求更换不同部件。可选夹层结构，以方便对泵加热或冷却，可以选择是否带安全阀，可以选择不同的密封形式，详见密封结构图。泵的各个零件可以选用不同的材质以适应具体使用要求。

　　不同的使用条件，泵的结构形式可能不同，具体应用请向厂家或本公司客户代表咨询。需要指出的是泵的转速愈高，泵的磨损愈严重，液体中如含有磨料物质，泵的材料应选用耐磨材质，在此种工况下，泵的压力和转速都应降低，高温条件下，则应增加泵的间隙，并采用耐热材料。

　　流动稳定：流量与齿轮转速成正比，与压力无关

　　流动平稳：没有脉动和压力波峰，不会产生管道颤动。

　　多功能性：仅仅通过调整转子轴的位置，同一台泵既可以出来稀释溶液又可以出来沥青，糖浆，树脂，聚合物等高粘度液体。

　　可逆性：可以通过改变齿轮的旋转方向使液体反向流动，两种方向都能充分发挥泵的性能

　　自吸性：由泵产生高真空，允许在zui大自吸高度实现快速自吸，取决于泵送液体的物理特性（温度，蒸汽压力，粘度等）。

　　建议性：只有两个活动部件：主动轮和动轮，只有一个轴封。

　　坚固的重载结构：低转速。特大球轴承的外部轴承座可以承受轴向和径向负载。

　　磨损率低：由于主动轮和从动齿轮不成倍数关系。这就意味着磨损可以被均匀的分散在每个齿轮上。因为一个齿轮上的每一个齿轮接触另一个齿轮上的每一个齿轮的次数一样。

磨损调节系统：转子边缘的磨损可以通过调整转子轴的位置来补偿。这样，即使在有相当大的磨损的情况下，也可以保证泵的稳定性。

　　维护简单，维护率低：不用移动泵，管道或泵驱动装置就可以进行检查和调节。

　　互动性：标准组件的设计可实现不同材料和特性零部件之间的替换。例如：有多种轴封系统可供选择，还可以安装带夹套的外壳和轴盖来代替标准部件。

　　端口位置可改变：泵壳可在轴承箱上旋转以从不同位置处吸排液体。

　　预热：加热夹套或是与外壳铸成一体，或是安装在端盖上，或是安装在填料压盖上。

　　旁路安全阀：旁路安全阀安装在泵上并且容易调节，在有些型号的泵上采取双重安全阀并带加热夹套。

●高粘度泵使用时注意事项mattersneeding attention when using high viscosity pump

　　进、出口管路的管径必须和泵保持一致；thediameters of inlet and outlet piping must be consistent withpump;

　　设计管路时应尽量减少弯头，且弯头角度不宜过小，进口管线不宜过长，以免影响自吸。

　　启动前每个注油杯都应家润滑油，且保证每天加油一次。

　　泵在工作前应该点动启动电机，观察转向是否和规定转向一致。

　　开机后观察运转是否正常，如有不正常噪音、特殊振动或温升过高等情况，应停机检查。

　　注意皮带松紧是否恰当，每半年调整一次。　

●nyp高粘度泵的进出口

　　泵进出口的型式

　　常规泵进出口尺寸相同，进出口呈垂直布置，从驱动机向泵头方向看为右进上出。也可根据客户需要，加工成水平进出口型或左进上出型。连接方式有法兰型和螺纹型.

　　泵进出口负荷

　　泵在安装时，应限制泵的进出口所承受的管路负荷。螺纹联接的管接头不得承受负荷，否则会使泵的联接管产生松动或旋紧力矩（管螺纹联接处不允许有旋紧或松动的扭矩，以免）影响管路的联接效果。

　　●高粘度齿轮泵并不能产生压力，它只是输出流量。压力低或无压力，说明高粘度齿轮泵没有吸入液体或泄漏严重。high viscosity gear pump does notgenerate pressure, it is only the output flow.pressure is low or nopressure, high viscosity gear wheel pump don't inhale the liquid orleakage is serious.

　　电动机输出功率偏小、齿 轮泵排量选得过大或压力调得过高时，也会造成压力不足当然，压力表损坏或压力表节流孔堵塞时也显示不出压力，此时可换装一个新的压力表检查。smallmotor output power, gear wheel pump capacity to choose too large orpressure too high, can cause stress pressure gauge damage orpressure gauge orifice jams, of course, also could not showpressure, can change a new pressure gauge to check at thistime.

　　如果确认泵无流量输出，可能是由于泵安装有误、泵的转向不对，或吸人侧(进液口及吸液管道)堵塞、出口止回阀装反或卡死了，也有可能是驱动轴断裂了。ifconfirmed that no flow pump output, could be turned to the pumpsdue to pump installation is wrong, wrong, or suction side (li the mouth and suck liquid pipeline jam, export check valveinstalled backwards, or card is dead, it is possible that the driveshaft fracture.

　　高粘度泵在转速过低时会引起出液量不足，这种现象往往是由于泵的驱动装置打滑或功率不足所致。此时应检查齿轮泵的实际转速、泵与电动机的联接及功率匹配情况等。high viscosity pump inlow speed can cause insufficient of produced liquid, thisphenomenon is often due to the slippage of the pump drive orinsufficient power.check the gear wheel pump at this time of theactual speed, pump and motor connection and power matching,etc.

　　  河北远东泵业制造有限公司坐落于铸造名乡—河北省泊头市。公司占地面积38650平方米，建筑面积20300平方米，是国内的集设计、铸造、生产、销售、服务于一体的容积泵专业制造厂家。公司始建于1984年,有二十几年专业研制经验。目前产品设计采用国际先进水平实体设计软件；产品研发、制造、检验、交付按照iso9001质量管理体系控制过程质量；产品制造广泛使用加工中心、数控机床、专用精机、高精设备；检测设备拥有工具显微镜、渐开线检测仪、光学投影仪、测齿仪、脉冲辉光离子氮化炉等大型检测设备，并建有国家b级试验站。本厂以的产品水平、优质的售后服务、恪守信用而在市场上倍受欢迎，产品畅销不衰，赢得了用户的普遍赞誉。公司已通过iso9001：2000国际质量体系认证，中国船级社ccs型式认证，法国船级社bv产品工厂认证，美国船级社abs产品质量认证，中国渔业船舶检验局船用泵认证,成为中石油物资资源市场成员、中石化物资资源市场成员。河北省知名产品生产企业，船用泵产品承制企业。hebeifar east pump industry manufacturing co., ltd is located in botoucity, hebei province, a casting of the township.the company coversan area of 38650 square meters, construction area of 20300 s, is the domestic famous design, casting, production, salesand service in one of the positive displacement pump professionalmanufacturer.company was founded in 1984, has 20 years experiencein professional development.the current product design adopts theinternational advanced level entity design software;productresearch and development, manufacture, inspection, delivery, inaccordance with the iso9001 management system of process control;widely used products manufacturing processingcenter, numerical control machine tools, precision machine, highprecision e;testing e has universal toolmicroscope, involute tester, optical projector, universal geartester, pulse glow ion nitriding furnace and other large-scaletesting e, and built national b level test station.thefactory with the first-class products, excellent after-salesservice, abide by credit and popular in the market, the productssell well and win the user's universal praise.the company haspassed iso9001:2000 international system certification,china classification society ccs type approval, bureau veritas bvproducts factory certification, the united states classificationsociety abs product certification, china's marine fishingvessel inspection bureau pump certification, has been a member ofthe material resource market in oil, sinopec material resourcesmarket member.well-known products production enterprise in hebeiprovince, marine pump products enterprises.

   公司以“泊远东”牌齿轮泵，螺杆泵为主导产品，涉及21个系列，4200多种规格，年生产能力达43000多台（套）。产品行销油田、化工、电力、船舶、冶金、食品等各大行业。产品除满足国内客商的需求外，部分出口至东南亚、美洲、欧洲等国家和地区。公司在全国各大城市设有30多个分支机构，并建立了完善的营销服务网络，拥有一支庞大敬业的营销服务队伍，可为广大客户提供优质的服务。公司以严谨的质量体系、先进的生产设备、完善的检测手段、丰富的制造经验、务真求实的远东团队，来有效保证产品质量。以满腔真诚期待与国内外各界人士携手铸就多方共赢的。companyto "moored far east" brand gear pump, screw pump for the leadingproduct, involves the 21 series, more than 4200 kinds ofspecifications, annual production capacity of more than 43000taiwan (sets).product marketing oilfield, chemical industry,electric power, shipbuilding, metallurgy, food and other majorindustry.products in addition to meet the needs of domesticcustomers, some exports to southeast asia, the americas, europe andother countries and regions.the company has more than 30 branchesin major cities throughout the country, and established a perfectmarketing service network, has a large professional marketingservices team, can provide the high service for thecustomers.companies with strict system, advanced productione, perfect detection means, rich manufacturing experienceand wuzhen strives for the far east team, to effectively ensure the of products.to sincerely look forward to working withpeople from all walks of life both at home and abroad hand in handto own a bright multi-win-win situation.

   我公司是一个生产齿轮油泵和螺杆泵的专业公司。公司拥有各种设备80台,主要设备有：c6140  cw6163c车床24台，tx611c/4镗床2台，m131m7130磨床8台，c125a立车2台，y318ky3150e滚齿机6台，e3050x16/1摇臂钻床2台，e5163立式钻床2台，b1-400铣床3台，螺杆泵转子专用铣床1台，半自动螺旋转子铣床2台，x53k立铣3台，半自动螺旋转子磨刃机台。my company is a companyspecialized in the production of gear oil pump and screwpump.company has 80 sets of various devices, the main eare: c6140 cw6163c 24 sets of lathe, tx611c/boring machine 2 units,4 m131m7130 grinding machine 8 units, c125a set, 2 sets, y318ky3150e hobbing machine 6 units, e3050x16/1 radial drilling machine2 sets, e5163 vertical drilling machine 2 sets, b1-400 universalmilling machine 3 units, screw pump rotor 1 millingmachine, semi-automatic screw rotor - b milling machine 2sets, x53k three vertical milling, semi-automatic screw rotor edge grinding machine is used.

    我公司拥有省计量局制试验台1台，自制试验台3台，使生产产品从原材料投入到产成品出厂实现了全过程检测。产品出厂合格率 ，具备较强的综合配套制造能力。理化试验室、长度计量室是国家计量确认合格单位，使产品从原材料投入到产成品出厂实现了全过程检测。产品出厂合格率，具备较强的综合配套制造能力，公司年可生产各种泵 6000多台。my company has the province system test bench1 bureau of standard measurement, homemade test-bed 3 units,production of products from raw materials into finished goodsfactory implements the whole process of detection.product factory rate , have strong ability of comprehensivemanufacturing.physical and chemical laboratory, length measuringroom is the national metrological confirmation unit, make ourproducts from raw materials into finished goods factory implementsthe whole process of detection.product factory rate ,have strong comprehensive manufacturing capacity, company canproduce all kinds of pump in more than 6000 units.

运费说明:

   1.本公司常规产品1-3天发货,特殊要求或者需定做的产品发货时间已与客户协商为准,2.泵运费方式有两种:快递和物流.小泵和小型配件发快递,其余体积较大,数量较多,推荐走专线物流货运,一般南方,中部地区及沿海地区3-5天左右到达.西部,北部较远的地区以及少数二次中转地区5-8天左右可到,具体覆盖范围请咨询公司客服人员.安装使用:请您根据产品说明书的步骤进行操作,如有问题,请联系我公司,我公司将会请zui专业的技术人员为您提供服务.为了保护您的利益,我们已经提醒客户在收到货物时,要开箱验货,如在打开验货时发现货物丢失,损害或者不符,请拒绝签收,您签收就代表已准确无误的收到后屋,若在签收货物之后才发现货物丢失或者不符,如不负责. 客户收到货后,产品无法安装或者规格有误,本公司提供退货或者换货服务,退货或者换货的客户请保证货物的完好无损,并承担往返运费. 客户收到后,如果产品存在质量问题,请在收货后7天内联系我公司,提供相关质量问题图片,我公司将在第一时间给您退货或者换货,因为我公司已经在发货前已经仔细检查过,所以过期将不提供此项服务,还请谅解.shipping details:1. ourregular products 1-3 days of delivery, special requests or need tocustom-made product delivery time is already negotiate withcustomer, 2. the pump freight way has two kinds: express andlogistics. small pump and small accessories send express, the restof the volume is larger, the number is more, recommend special linelogistics, freight, generally south, central and coastal area about3 to 5 days to arrive. in the west, north of remote areas and areasinhabited by minority secondary transit, about five to eight daysto specific coverage please consulting company customer servicestaff. install and use, please according to the product manualsteps, if any problem, please contact our company, we advise youthat we will be the most professional and technical personnel toprovide service for you. in order to protect your interests, whenwe have to remind the customer receive the goods, unpackinginspection, such as when open the inspection found that the goodslost, damage or discrepancy, please refuse to sign after receivingsth, you sign after receiving sth means have accurate receivedafter the house, if after receipt of goods found the goods didn'tagree lost or, if not responsible. customers after receiving thegoods, the product can't install or specification is wrong, thecompany provides the return or exchange service, return or exchangethe customers please make sure that the goods are intact, and bearthe freight back and forth. the receipt of the customer, if theproduct problems, please contact me within 7 days afterreceiving the company, provide relevant problem photos, ourcompany will give you a refund or a replacement in the first time,because i already have carefully checked before shipment, so latewill not provide this service, also please understand.