厂家供应NABZC全自动变比组别测试仪

 产品简介

用变比电桥测量变压器的变比，操作过程繁琐、测量范围狭窄，已经不适应现代测量快节奏、效率高的要求。为此，南澳电气（武汉）有限公司采用现代电子技术，研制出了新一代全自动变比组别测试仪。它体积小，重量轻，精度高，稳定性好。它采用了大屏幕中英文液晶屏显示、内置中英文菜单式操作，完成一组变压器的测试只需11秒。nabzc全自动变比组别测试仪是电力工业部门的理想测试仪器。

产品别名

变压器变比组别测试仪、变压器双臂电桥

产品特性

1．自动测量接线组别。

2．自动进行组别变换。

3．自动切换相序。

4．自动切换量程。

5．自动校表。

6．输入标准变比后，能自动计算出相对误差。

7. 一次测量完成，自动切断试验电压 。

8. 设置数据,测量结果自动保存，可查看以前数据。

9. 测量有载变压器,只输入一次变比。

产品参数

1．变比测量范围： 1—10000

2．组别：1—12点

3．精度: 1-1000 0.2 级 1000-10000 0.5级

4．电源：ac220v ±10%，50hz

5．使用环境温度：-5℃─ 40℃

6．使用环境湿度：＜85%

7．体积：430mm×320mm×215mm

8．重量：8kg

注意事项

1. 保险1为2a,保险2为0.5a。如果测试线短路,高低压接反,会熔断保险。保险熔断后，如果进行测量，在显示“ 正在测量，请等待！”后停住。请关机，更换相同容量的保险，重测。

2.连线要保持接触良好。仪器应良好接地！

3.仪器的工作场所应远离强电场、强磁场、高频设备。供电电源干扰越小越好，宜选用照明线,如果电源干扰还是较大，可以由交流净化电源给仪器供电。交流净化电源的容量大于200va即可。

4.仪器工作时，如果出现液晶屏显示紊乱，按所有按键均无响应，或者测量值与实际值相差很远，请按复位键,或者关掉电源,再重新操作。

5.显示器没有字符显示,或颜色很淡,请调节亮度电位器至合适位置。

亮度电位器是多圈电位器 ，有10圈！

6.仪器应存放在干燥通风处，如果长期不用或环境潮湿，使用前应加长预热时间，去除潮气。

7.通讯口调试时使用。

productintroduction

when using this radiobridge to measure the transformer ratio, the operation procedure iscomplex, the measuring measure range is narrow, which is no longermeet modern fast-paced, high-efficiency re therefore,nabzc electricaluses the modern electronic technology, developed a new generationof automatic variable ratio group tester. it is small, light, highaccuracy and with good stability. it uses a large-screen characterdisplay, menu operation, friendly interface. the variable group canmeasure at once. nabzc automaticvariable ratio group tester is ideal product for electricalindustry department.

alsocalled name

transformer ratio group tester, transformer ratio tester,transformer ratio automatic tester, automatic transformer ratiotester, transformer ratio group testing device, transformer ratiotesting device, transformer ratio automatic testingdevice.

thecharacteristics of the products

1. automatic measurement wiring group.

2. automatic group transformation.

3. automatic switching phase sequence.

4. automatic shift ranging.

5. automatic calibration.

6. input the standard ratio, it can automatically calculate therelative error.

7.when the measurement is completed, it can cut off the testingvoltage automatically .

8. setting the data, the measured results can be savedautomatically, and can be view the previous data.

9. measuring loaded transformer ratio, only need to enteronce

theparameters of the products

1. ratio measuring range: 1-10000

2. group:1-12:00

3. accuracy: 1-1000  0.2 grade,1000-10000 0.5 grade

4. power supply: ac220v ±10%, 50hz

5. operating temperature: -5 ℃─ 40 ℃

6. operating humidity:<85%

7. volume: 430mm × 320mm × 215mm

8. weight: 8kg

power supply: ac110v/115v/120v/127v/220v/230v/240voptional

input frequency: 50hz/60hz optional

note: the users can select the corresponding power which based ontheir local supply voltage and frequency, and we will confirm itbefore the delivery (or inform us that the goods will be used inwhich country advance)

attentionsshould take

1.insurance 1 is 2a, insurance 2 is 0.5a. if the testing line isshort-circuit , the high and low voltage will be reversed, willburn the fuse. once fused, it will be displayed " measuring , wait! " and then stop to operate and cut off the power.please replacethe same capacity insurance, then retesting .

2.maintain the connections is fine. the instrument should be wellgrounded !

3.ensure the workplace keep away from strong electric field ,magnetic field anduency devices. power supplyinterference should be the smaller the better, and use light line.if the power supply interference is still large, it better to usethe ac purified power,.the purified ac power supply capacity justlarger than 200va will do.

4.during the operating, if there is disorder on lcd screen, andwithout any response after press all the button, or the measuredvalue is much very far away from the actual value, please press thereset button, or turn off the power, then restart the operate.

5.if the displays without character display ,or the color is weak,please adjust the brightness potentiometer to the appropriatelocation . brightness potentiometer is a multi-turn potentiometerwith 10 laps !

6.the instrument should be stored in dry and ventilated place , ifunused for a  long-term, or stored in a humid environment, itneed to extend the warm-up time before using , to remove  themoisture.

7.communication port used for debugging .