输送黄油泵KCB33.3齿轮泵

输送黄油泵kcb33.3齿轮泵kcb33.3(2cy2/1.45)流量:2m3/h压力:1.45mpa口径:g3/4",配电机y100l14

 ●kcb齿轮泵性能范围

　　主要用于油田、油库、港口、码头、船舶等大流量输油，卸油

　　应用范围:kcb/2cy型齿轮输油泵适用于输送粘度在300c.s.t以下的各种油类，如原油、柴油、润滑油、动植物油等。配用铜齿轮可输送低闪点液体，如汽油、苯等。介质温度不超过70℃，耐高温油泵的使用温度不超过300℃。本泵身带有安全阀，超载时起安全作用。轴封有骨架油封、机械密封、填料密封三种型式，订货注明。kcb齿轮润滑泵主要用于各种机械设备中的润滑系统中输送润滑油，适用于输送粘度在10oe（75c.s.t）以下，温度在300℃以下的具有润滑性的油料，不锈钢齿轮泵可输送食用油料、饮料等。轴封有骨架油封、机械密封、填料密封三种型式.

 ●kcb齿轮泵安装说明:kcb gear pump installation instructions:

　　1、安装泵的地点应足够宽敞，以方便检修工作。1, thelocation of the installation of pump should be spacious enough, tofacilitate maintenance and repair work. the stand or fall of2、泵安装的好坏，对泵的平稳运行和使用寿命有很重要的影响，所以安装校正工作必须仔细地进行，不得草率行事。2,pump installation, for the smooth running of the pump and servicelife have very important influence, so the installation calibrationwork must be carried out carefully and must not be too hasty.3、泵吸入管的安装高度、长度和管径应满足计算值，力求简短，减少不必要的损失（如弯头等）；并保证泵在工作时，不超过其允许汽蚀余量。4、吸入和排出管路应该有支架。泵不允许承受管路的负荷。3,installation height of pump suction pipe, the length and diametershould satisfy the calculated value, to short, reduce unnecessarylosses, such as elbow, etc.); and ensure the pump at work, no morethan the allowed npsh. 4, suction and discharge line should be asupport. pump are not allowed to bear load of pipeline.

●kcb齿轮泵安装: kcb gear pumpinstallation:

　　1、泵安装前应检查泵和电机在运输过程中是否受到损坏，如电机是否受潮，泵的进出口防尘盖是否损坏而使污物进入泵腔内等。1,before the pump installation, should check the pump and motor isdamaged during the transit, whether be affected with damp beaffected with damp such as motor, pump the import and export ofdust cover for damage and make the dirt into the pump chamber,etc.

　　2、泵在搬运过程中，应选择合适起吊位置，减少泵的变形。2,pump in the process of handling, should choose appropriate liftingposition, reduce the deformation of the pump.

　　3、泵的底座应固定在牢固的基础上，以免产生振动影响泵的正常工作。3, the base of the pump should be fixed on the basis of thestrong, so as to avoid vibration influence the normal work of thepump.

　　4、泵的进出口管路应清理干净不得存有硬颗粒的报告杂物。4,import and export of pipeline of pump should be cleaned up shallnot have the report of hard particles sundry.

　　5、管路口径一般不小于泵的进出口径，进油管路应尽量短，并减少弯路。必要时在进油口安装金属过滤器，过滤器的有效面积不应小于管道过流面积的三倍。5,pipe diameter is generally not less than the in and out of thecaliber of pump, the oil pipeline should be short, as far aspossible and less detours.when necessary, metal filter is installedon oil inlet filter effective area should not be less than threetimes of pipe flow area.

　　6、安装时，不得用泵来承担管路的重量。7、用手转动联轴器，泵应转动灵活，不得有过紧或轻重不均现象，如有应立即排除。

6, when installation,must not use the pump to bear the weight of the line.7, turn thecoupling with the hand, the pump should be flexible rotation, cannot have too tight or weight uneven phenomenon, should immediatelyruled out.

●kcb齿轮泵概述

　　kcb齿轮油泵在输油系统中可用作传输、增压泵；kcb gearoil pump in the oil system can be used as a transport, boosterpump;

  在燃油系统中可用作输送、加压、喷射的燃油泵；in the fuel system can beused as a transport, pressure, jet fuel pump;

  在一切工业领域中，均可作润滑油泵用。in all industrial areas, canbe used as lubricating oil pump.

  kcb齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。齿轮经热处理有较高的硬度和强度，与轴一同安装在可更换的轴套内运转。泵内全部零件的润滑均在泵工作时利用输出介质而自动达到。kcbgear pump are mainly gear, shaft, pump body, valve, shaft end seal.gear after heat treatment with high hardness and strength, andshaft installed in the replaceable shaft sleeve. in all parts ofthe lubrication pump are pump work automatically to achieve usingthe output media.

  泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力小，因此轴承负荷小，磨损小，泵效率高。pump is the drainage and back into the groove of reasonabledesign, is a gear in the work under the minimum torque force, sothe bearing load is small, wear small, pump with highefficiency.

  泵设有安全阀作为超载保护，安全阀的全回流压力为泵额定排除压力的1.5倍，也可在允许排出压力范围内根据实际需要另外调整。但注意本安全阀不能作减压阀的长期工作，需要时可在管路上另行安装。从主轴外伸端向泵看，为顺时针旋转。pumpis e with safety valve as overload protection, the totalreflux pressure relief valve is rated pump out pressure of 1.5times, also can allow discharge pressure range according to actualneeds and adjust. but note that this cannot be a long-term workpressure reducing valve, relief valve can be installed in thepiping shall be separately when necessary. to pump from the mainshaft overhang end to see, for clockwise.