法国SIDEL吹瓶机电路板维修

 北京慧博时代科技有限公司(简称“慧博科技”)是一家中国的专业维修工控设备的大型公司，总部位于首都北京，创建于2001年，经过十多年的发展，今天,慧博科技已经在中国3大中心城市（北京、上海、深圳）拥有分公司。

法国sidel吹瓶机电路板维修

故障类型:一类故障(设备停机不能开机)
故障名称                1.   e19.5 紧急制动
  故障原因                  检查k1.a以及plc输入及紧急按钮

  故障名称             2.   e10.5主电停
  故障原因                  检查q1和q1的保险丝.
                             检查是否有紧急制动按钮按下
  故障名称                3.  e10.2 没有24vdc
  故障原因                    检查q1e是否合上                             
  故障名称                4.   e19.6没有24vdc
  故障原因                    检查q1e是否合上
  故障名称               5 .   e10.4门开着
  故障原因                    检查门是否关上及门接触器                                 
  故障名称                6.   e36.6-e37.7没有24vdc
  故障原因                    检查q1l及q1f
故障名称                7.   e17.0-e17.7-e18.0-e18.7
                                      门开着
  故障原因                    检查门是否关上及门接触器            
                                          
  故障名称                8.   e16.0-e16.6紧急制动被按下
  故障原因                    检查紧急制动按钮并复位
   故障名称                9.   e8.0 炉子力偶
  故障原因                    检查炉子是否有异物卡住.                                   
                                    芯轴链轮是否运转不良
                                    扭力限制器是否松动及损坏
                                    检查完后再用摇手复位 
                                         
  故障名称                10.   e8.1主马达扭力
  故障原因                    检查有无异物卡住吹瓶机
   故障名称                11.  e8.2  输出轮过载
  故障原因                    检查是否有瓶子等异物卡住                                     
                                     并检查输出轮位置  
                                        
  故障名称                12.   e8.5进胚轮过载
  故障原因                    检查是否有异物卡住
                                    并检查进胚轮位置           
   故障名称                13.   e8.7摇手柄安全开关 
  故障原因                    检查摇手柄是否拿下
                                    翻板是否复位
                                    电眼工作是否正

  故障名称                14.   e11.0主马达变频器跳闸
  故障原因                    检查刹车是否松开
                             检查吹瓶轮有无阻碍其转动的物体           
   故障名称                15.   e11.1 主马达变频器故障
  故障原因                    检查变频器的设定及线路                                   
                                          
  故障名称                16.   e11.2主马达继电器故障
  故障原因                    检查k69.ca是否合上
   故障名称                17.   e23.3瓶胚臂上没有夹子
  故障原因                    检查电眼及连线                                      
                                     检查电眼与机械手之间的间隙                                          
                                     检查机械手凸轮是否有异物

  故障名称                18.   e14.0汽缸压力故障
  故障原因                    检查7公斤压力供给和其压力
                                    检查压力开关s14.0的设置       
                                检查7公斤主电磁阀工作是否正常
   故障名称                19.   e19.7 工具安全
  故障原因                    检查是否将调整工具复位                                      
                                     检查电眼是否损坏  
 
  故障名称                20.   e14.1刹车没有松开
  故障原因                    检查刹车是否有异物卡住
                                    检查s14.1工作是否正常             
                                           
   故障名称                21.   e21.7 炉子通风变频器故障
  故障原因                    检查变频器工作状况                                    
                                主要生产全自动吹瓶机          
  故障名称                22.   e23.1出瓶轮活动导轨错位
  故障原因                    检查有无异物卡住
                                    检查b23.1电眼             
   故障名称                23.   68#光栅编码器无步进 
  故障原因                    检查电线接头和编码器的工作                                     
                                          
  故障名称              24.   69#机器步进电眼b12.6故障
  故障原因                    检查b12.6的设定及连线
   故障名称             25.   e23.2炉子出口活动导轨错位
  故障原因                    检查有无异物卡住                                   
                                     检查b23.2电眼

  故障名称                26.70#凸轮起始位故障 
  故障原因                    重新启动plc
   故障名称                27.   71# 电眼凸轮数据错误
  故障原因                    重新启动plc                                    
                                          
  故障名称                28.   72#plc故障
  故障原因                    查plc工作是否正常
                                                
故障名称                29.   e12.4机器转速电眼故障
  故障原因                    检查b12.4电眼的设定及连线                               
                                     plc工作温度过高
                                     检查空调运转是否正常

  故障名称                30.   e36.0吹瓶机起始位置故障
  故障原因                    检查36.0电眼的设定及连线
                                    检查36.0的位置是否准确             
                                           
故障名称                31.   e12.6机器步进电眼故障
  故障原因                    检查12.6电眼的设定及连线                               
                                     检查12.6电眼的位置是否准确

  故障名称                32.e13.5进料同步电眼故障   
  故障原因                    检查13.5电眼的连线及设定
                                    检查13.5电眼的位置是否准确         
                                          

故障名称              33.   e21.2炉子通风设定值不正确
  故障原因                    检查变频器的设定值                                   
                                          
  故障名称                34.79#由于灯管破损而停机   
  故障原因                    检查有无异物将灯管卡坏
                                    检查欠流继电器             
                                           
故障名称                35.   80#没有设定参数
  故障原因                    检查机器参数设定情况                                      
                                         

  故障名称                36.   e14.2没有40公斤高压气
  故障原因                    检查空压机是否打开
                                    检查s14.2压力开关             
故障名称             37.   88#吹瓶机电磁阀控制器故障(6公斤)
  故障原因                    检查调压阀的工作是否正常                                      
                                         

  故障名称                38.   89#喷嘴汽缸压力超出范围
  故障原因                    检查有无压力及其控制回路
                                    检查并更换喷嘴密封件     
故障名称               39 .   e9.0开合模臂故障
  故障原因                    检查开合模臂位置并调整                                     
                                      检查开合模臂是否下降

  故障名称                40.   e9.1某号模具有异物
  故障原因                    检查模具中是否有瓶子等异物
                                        
故障名称                41.   e9.2某号喷嘴不干净 
  故障原因                    检查是否有物体粘在喷嘴上                                     
               

  故障名称                42.   e9.3底模上升凸轮应力
  故障原因                    检查底模上是否有异物
                                    检查b9.3电眼工作是否正常             
                                           
故障名称                43.   e9.4某号拉伸杆未上升
  故障原因                    检查拉伸电磁阀工作是否正常                                  
                                       电磁阀线圈坏及更换
                                      拉伸汽缸密封件坏更换
  故障名称                44.   e9.5某号模具未锁
  故障原因                    检查锁模臂位置是否正常
                                      检查模具补偿螺丝是否有断裂现象            
                                      检查模具是否安装到位
                                      检查补偿电磁阀是否坏
                                      检查底模与模身的间隙是否正常
   

北京总部：北京市朝阳区霄云路18号京润水上花园d区29号；

电    话：010-88459351/88459352

上海分部：上海市宝山区华灵路1225弄华欣苑38号

电    话：021-54257837/

深圳分部：广东省深圳市鸿进路鸿基花园三期3栋b1108 

电    话：0755-84576463/84576481

公司网址：www.huibogs.com