低摩擦PTFE 7A X美国杜邦 电器导线绝缘材料 7A X
- 供应商
- 京冀(广州)新材料有限公司
- 认证
- 报价
- ¥27.00元每千克
- PTFE
- 耐化学性良好
- 7AX
- 抗溶剂性密封件
- 美国杜邦
- 低摩擦低烟度
- 联系电话
- 18938547875
- 手机号
- 18938547875
- 联系人
- 蒋红卫
- 所在地
- 广州市南沙区丰泽东路106号(自编1号楼)X1301-E014087(注册地址)
- 更新时间
- 2024-05-07 07:10
用途:
各类聚四氟乙. 烯制品已在化工、机械、电子、电器、航天、环保和桥梁等国民经济领域中起到了举足轻重的作用。
四氟乙.烯板适用于-180℃~+250℃温度下,主要用作电器绝缘材料及接触腐蚀介质的衬里、支承滑块、道轨密封件及润滑材料,富柜家具把它用于轻工业中,广泛应用于化工、医药、染料业容器、贮槽、反应塔釜、大型管道的防腐衬里材料;航空、军事等重工业领域;机械、建筑、交通桥梁滑块、导轨;印染、轻工、纺织业的防粘材料等.
外观标准:
(1)板材的颜色为树脂本色。
(2)应质地均匀,外表平整,不允许有裂纹、气泡、分层、机械损伤、刀痕等缺陷。
(3)允许有轻微云斑状的松紧现象。
(4)允许有10×10cm面积上存在直径为0.1-0.5mm非金属杂质不超过1个,直径为0.5-2mm的非金属杂质不超过1个。
zonyl mp1100(4微米)
zonylmp1100氟添加剂是一种白色的自由流动的ptfe粉末,旨在作为其他材料中的添加剂使用,以提供低表面自由能和其他氟聚合物特性。特别重要的是,已有发现证明它非常适用于油墨和涂层应用,这些应用对颗粒的均匀性有一定要求。与塑料和弹性体一起使用时,还可增强润滑性能和耐磨损性能。如果将其加入润滑剂中,可以增强严苛条件性能。zonyl?mp1100可应用于–190到250°c(–310到480°f)的温度条件。
zonyl mp1200(3微米)
使用,以提供低表面自由能和其他氟聚合物特性。特别重要的是,已有发现证明它非常适用于油墨和涂层应用,这些应用对颗粒的均匀性有一定要求。与塑料和弹性体一起使用时,还可增强润滑性能和耐磨损性能。如果将其加入润滑剂中,可以增强严苛条件性能。zonylmp1200可应用于–190到250°c(–310到480°f)的温度条件。
polytetrafluoroethylene
dupont fluoropolymers
产品说明:
teflon ® ptfe 7a x is a white powder with small particle sizeand high bulk density. the small particle size of teflon ® ptfe 7ax helps to minimize voids even at relatively low molding pressures.high bulk density increases the size of moldings possible from agiven mold or press opening. teflon ® ptfe 7a x is preferred forlarge moldings, such as billets, re optimum mechanical andelectrical properties. it is also used in a mixture with fillerswhen they are added to modify the mechanical properties ofmoldings. properly processed products made from neat teflon ®ptfe7a x provide the superior properties typical of the fluoroplasticresins: retention of properties after service at 260 °c (500 °f),useful properties at -240 °c (-400 °f), chemical inertness tonearly all industrial chemicals and solvents, and low friction andanti-stick surfaces. dielectric properties are outstanding andstable with frequency and temperature. molded products havemoderate stiffness and high elongation.
teflon ® ptfe 7a x resists ignition and does not promote flame
spread. when ignited by flame from other sources, the contributionof heat is small and with little smoke. statements, or data,regarding behavior in a flame situation are not intended to reflecthazards presented by this or any other material when under actualfire conditions.
typical applications
many end products are fabricated from moldings of teflon ® ptfe 7ax, including skived film and sheet, gaskets, packings, mechanicalseals, bridge or pipeline bearing pads, shaft bearings, electricalinsulators, piston rings, expansion bellows, diaphragms, andchemical linings. the use of fillers provides a wide choice ofmodified mechanical properties.
物性信息:
展开全文