PBT耐高温BK注塑级阻燃

pbt工艺特点：
pbt注塑之前一定要在110～120℃的温度下干燥3小时左右，成型加工温度为250～270℃，模温控制在50～75℃为宜。因该料从熔融状态一经冷却，则会立即凝固结晶，故其冷却时间较短；若喷嘴温度控制不当（偏低），流道（水口）易冷却固化，会出现堵嘴现象。若料筒温度超过275℃或熔料在料筒中停留时间超过30分钟，易引起材料分解变脆。pbt注塑时需用较大水口进胶，不宜使用热流道系统，模具排气要良好，宜用“高速、中压、中温”的条件成型加工，防火料或加玻纤的pbt水口料不宜再回收利用，停机时需用pe或pp料及时清洗料管，以免碳化。                                                                                                                                                            processfeatures: pbt must be dried at 110-120 ° c for about 3 hours beforeinjection molding, molding temperature is 250-270 ° c, moldtemperature is 50-75 ° c. if the temperature of the nozzle isimproperly controlled (on the low side) , the flow channel (nozzle)is easy to be cooled and solidified, and the nozzle will beblocked. if the barrel temperature exceeds 275 ° c or the moltenmaterial stays in the barrel for more than 30 minutes, it is easyto cause the material to decompose and become brittle. pbtinjection needs larger inlet glue, not hot runner system, moldexhaust should be good, suitable for"high speed, medium pressure,medium temperature" molding conditions, fireproof material or pbtnozzle material with glass fiber should not be recycled. pe or ppmaterial should be cleaned in time to avoid carbonization.                 

特性良好粘结性冲击性能 额定值 单位制 测试方法简支梁缺口冲击强度 (23°c) 7.0 kj/m² iso 179/1ea可燃性额定值 单位制 测试方法ul 阻燃等级 hb ul 94热性能 额定值 单位制 测试方法热变形温度 (1.8 mpa, 未退火)206 ℃ iso 75-2/a线形热膨胀系数横向 : 23 到 55°c 1.0e-4 cm/cm/°c 内部方法流动 : 23 到55°c 4.0e-5 cm/cm/°c 内部方法电气性能 额定值 单位制 测试方法体积电阻率 6.0e15 ohms·cm iec60093介电强度 (3.00 mm) 19 kv/mm iec 60243-1

加工条件干燥温度（℃） 110～120 干燥时间约（hr） 2～3模具温度（℃） 50～75 残料量（mm） 2～6熔胶温度（℃）250～270 背压（mpa） 5～10注射压力（mpa） 100～140 锁模力约(ton/in2) 3～4注　塑　速　度 高　速回料转速(rpm) 70～90螺　杆　类　别 标　准　螺　杆（直　通　式　喷　嘴）停　机　处　理 关料闸啤清即可 碎料翻用（%）15～25备注：防火pbt需要用pe料过炮，水口料不宜回收利用。

standard test method for notched impact strength of simplysupported beams (23 ° c)7.0 kj/m 2 iso 179/1ea flammability,rating, unit, test methods-ul flame retardant grade hul 94-thermalperformance, rating, system of units, test method thermaldeformation temperature (1.8 mpa, non-annealed)206 ° c iso 75-2 alinear coefficient of thermal expansion transversal: 23 to 55 ° c1.0 e-4 cmcmcm° c internal method flow: 23 to 55 ° c 4.0 e-5cmcmcm° c internal method electrical performance, rating, system ofunits, test method volume resistivity 6.0e15 ohms · cm iec 60093dielectric strength (3.00 mm)19 kv/mm iec 60243-1 processingconditions drying temperature (° c)110-120 drying timeapproximately (hr)2-3 mold temperature (° c)50-75 residue amount(mm)2-6 melt glue temperature (° c)250-270 back pressure (mpa)5-10injection pressure (mpa)100-140 clamping force approximately(ton/in2)3-4 injection speed high speed turn-back rate (rpm)70-90screw type standard screw (through nozzle) shut down to clean theclosing gate, scrap reuse (%)15-25 remarks: fire pbt needs to usepe material over the gun, nozzle material is not suitable forrecycling.