五档汽车加热座垫 通用 纤维

规格	通用	材质	纤维
款式	五档、分控	颜色	白、黑
品牌	德胜	产地	无锡

汽车座椅加热系统car seat heating system

一综合说明general information
此款产品是我们多年研究的结晶,在控制方面采用微电脑控制,温度任意调节,同时有30分钟定时功能.组成更为简单,只有两部分,由插到点烟器上的控制器和连体热片组成.发热部分采用高科技发热材料,升温快.this product is the result of our effort on researching anddeveloping through many years, the control system is controlled bythe micro-computer, the temperature is adjusting freely, with30minutes timing function. the product is made by only twosections, the controller which is plug in to the cigarette-plugplus pads, the heating element is adopted by hi-tech heatingmaterial, with the character of temperature raising rapidly.

二是您冬季的好伴侣your best companion in winter season
在每年寒冷的冬季,它升温快,温度任意调节,使您的腰酸腿疼有一定的缓解作用,对健康者-有一定的保健作用,可避免因寒风的入侵所引发的疼痛.inevery cold winter, this product will reducing your painful of yourwaist and back through it’s rapidly temperature-raising andtemperature-adjusting, it healthy to the people, to live away fromthe painful caused by cold wind.

三安装方法installation guide
1.将座椅的外座套取下,而后将发热片的背面双面胶撕开,再将发热片粘贴到座和靠背上,再把座套套好.贴热片时座和靠背粘贴时要成直角takeout the outer cover of the seat, tear off the double-side sticky,stick the heating pad into the bottom and back from the seat, thenre-cover the seat cover, it should be a 90degree angle whilesticking the bottom and back

2.将加热体的电极引出线从座和靠背的中缝处放于座椅下面.put the extend wire from electrodeat the bottom of the seat where the position of the seat andback

3.将温度控制器插到汽车点烟器的插座中.而后将控制器的插头和发热体的插座在座椅下方对接,这时座椅加温系统就安装好了.plugthe temperature controller into the cigarette-plug, to connect theconnector of controller with the connector of the heating padsunder the seat, then the whole heating system is installedwell.

四使用方法user’s manual
1.将温度控制器的开关从细的符号方向向粗符号方旋转,这时电源灯和调温灯同时亮,红灯为升温工作灯,绿灯为电源灯.turn theswitch of the temperature controller from thin-sign to thethick-sign, the indicator of power and temperature-adjusting willbe light-on at the same time, the red-indicator mean temperatureraising indicator, the green-indicator means power indicator.

2.调温开关上的温度指示符号越粗表示温度越高.即向粗符号方向旋转到某一位置不动后,表示把温度设定在此点上.the changesof thicker-sign of temperature indicator from temperature adjustingswitch means raising the temperature steadily, the temperature willbe set up wile you turn the switch to the thicker-sign and stay ina certain position.

3.如果在使用一段时间后发现温度较高,这时可向细符号方向旋转,将温度设定低一些.if you feel thetemperature is higher after you using it for a certain time, toreduce the set up temperature by turning the switch to thethinner-sign.

4.如果要关掉加热系统,只需将调温开关旋到温度调节符号小处后即可,这时控制器上的灯全部灭掉.if you wantswitch off the heating system, just turn the temperature adjustingswitch into the minimize of the sign, the indicator from thecontroller will be off at this time.

5.具有定时功能timing function

此控制器有30分钟定时功能,到30分钟后会自动关掉升温系统,如果需要继续使用,只需关了开关后再开一次即可.因为汽车有两种功能的点烟器,一种是关闭发动机后点烟器上没有电源输出,另一种是关闭汽车发动机后点烟器上仍有电源输出,这时如果忘关加温系统,停放一夜后汽车电瓶的电会被用掉一部分,造成第二天早晨启不着车.所以才设计了定时功能.thiscontroller has the ability of timing with 30minutes, the systemwill be shut off the automatic temperature raising after 30minutes.if you want go on to use it, just switch off the switch and open itonce again. this design is for that there are two functions ofcigarette from the car one is, there is no power on after switchoff the engine. another on is, there is still power on from thecigarette-plug after switch off the engine, for this kind ofcigarette, if you forget to switch off the heating system, it willbe consumed some power from car battery after one nigh parking,then it will cause the car starting trouble at the second morning,that’s the reason of this function desiged

五注意事项attention
1.控制器的点烟器插头要和汽车上的点烟器插座要插接牢固.it should be a solid connection betweenthe plug from controller with the cigarette-plug from the car

2.发热体要与汽车主驾驶的座和靠背粘贴牢固,并成直角.the heating pads should be sticksolidly and in 90degree angle to the bottom and back from the seatof car driver

新产品介绍五档拨轮分控

一综合说明
此款产品是我们多年研究的结晶,在控制方面采用微电脑控制,温度任意调节，组成更为简单,只有两部分,由控制器和连体热片组成.发热部分采用高科技发热材料,升温快.

二是您冬季的好伴侣
在每年寒冷的冬季,它升温快,温度任意调节,使您的腰酸腿疼有一定的缓解作用,对健康者有一定的保健作用,可避免因寒风的入侵所引发的疼痛.安装后使您的车有了车的享受。
三安装方法
1.将座椅的外座套取下,而后将发热片的背面双面胶撕开,再将发热片粘贴到座和靠背上,再把座套套好.贴热片时座和靠背粘贴时要成直角.

2.将加热体的电极引出线从座和靠背的中缝处放于座椅下面.

3.将温度控制器插到汽车原预留孔中.而后将控制器的插头和发热体的插座在座椅下方对接,这时座椅加温系统就安装好了.

四使用方法
1.温度控制器开关有三种：五档拨轮，九档拨轮，高低档开关。将温度控制器的开关从0，1，2，3，。。。的符号方向旋转即为把温度设在这些档位。这时电源调温灯同时亮,红灯为升温工作灯.

2.调温开关上的温度指示符号越大表示温度越高.即向数字大的符号方向旋转到某一位置不动后,表示把温度设定在此点上.

3.如果在使用一段时间后发现温度较高,这时可向数字小的方向旋转,将温度设定低一些.

4.如果要关掉加热系统,只需将调温开关旋到温度调节符号小处“0”后即可,这时控制器上的灯全部灭掉.

5．九档开关的使用和五档一样。高低档控温时，只有两档，和低档。中间档为关。
五注意事项
1.控制器的插头要和线上的插头要插接牢固.

2.发热体要与汽车主驾驶的座和靠背粘贴牢固,并成直角.

六．加热片的规格：
46cmx46cm;46cmx26cm;40cmx40cm;开孔热片，异形热片，尺寸可按用户要求生产。
七．功率：
20w,25w,30w,40w,45w,50w,55w,60w,65w,70w,75w,80w,85w,90w,95w,100w,110w,120w.

八．配套：

〈1〉。我们已给国内外多家整车厂配套。〈2〉。是汽车美容，汽车装饰，汽车维修，4s店产品。〈3〉。私家车也可方便安装。