【供应】对刀仪(无线高度设定仪)

供应商
成都海龟无线科技有限公司
认证
报价
150.00元每件
品牌
新宏畅
型号
无线对刀仪
类型
无线高度设定仪
联系电话
86 28 85238029
手机号
13980005532
联系人
罗国峰
所在地
成都市武侯区玉林东街16号

详细介绍

品牌新宏畅型号无线对刀仪类型无线高度设定仪规格高度设定仪适用机床皆可产品别名无线高度设定仪材质塑料是否库存否是否批发是

无线对刀器描述:

.无线与运动控制系统连接,无任何连接线

.无线传输距离15米

.对刀行程4毫米

.对刀精度6微米

.采用纽扣电池3v使用,工作电流小于200微安,能使用6个月不更换电池

.具有电源开关:平时不使用对刀器,将电源开关关闭,以节约电能,延长电池使用寿命

.外观尺寸:70毫米x 50毫米 x40毫米

.具有2级告警输出:当刀具压下对刀器往下移动,达到对刀点的时候,对刀器将对刀信号无线传输到运动控制卡,运动控制卡马上停止机床移动,达到对刀目的;如果机床没有停止移动,刀具继续移动,达到对刀器第2级告警,那么对刀器将第2级告警信号传输给机床,出发机床的z轴退刀点,迫使机床刀具回到z轴退刀点,保护刀具

.使用方便,适用性强,比传统对刀器更方便,工作效率更高

一.外观结构说明(structuredescription)

对刀器:heightsetting instruments

备注:当低压指示灯亮的时候,表示电池电量快用完了,建议更换电池。

note:when the low pressure indicatorlight when the battery is running out, the proposed replacementbattery

二.装箱配件说明(packingparts)

1.接收器(wirelessreceiver):1只(one)

2.无线对刀器(wireless height settinginstruments):1只(one)

3.说明书(manual):1份(one)

三.直流电气特性(dcdescription)

产品名称

name

工作电压

voltage

工作电流

current

备注

note

无线接收器

wirelessreceiver

4.5v—5.0v

小于50ma

less than50ma

无线对刀器

wireless heightsetting instruments

2.5v—3.0v

平均电流小于1ma

averagecurrent

less than1ma

3v纽扣电池供电,可以使用半年

3v button batterycan be used for 6 months

四.对刀性能参数

项目名称

project name

参数

parameters

备注

note

对刀行程

height settinginstruments

range

3mm

机床刀具接触到对刀仪探头后,可以活动的zui大距离

machine headscome into contact with the probe instrument,you can active the maximumdistance

重复对刀精度

repeatabilityofheight settinginstruments

小于6微米

less than 6microns

注意:无线对刀器采用3v纽扣锂电池工作,当低压指示灯亮的时候,表示电池电量快用完了,建议更换电池。

note:the height setting instrumentswork with 3v lithium coin;when the low pressure indicatorlight when the battery is running out, the proposed replacementbattery

更换电池:用十字螺丝刀把对刀器底盖拆下来,然后更换电池,再安装上对刀器底盖。

replacethe batteries:with a phillips screwdriver toremove the bottom cover and then replace the battery, then installthe bottom cover.

五.性能描述(rfperformancedescription)

序号

no.

性能参数描述

performance or parametersdescription

1

采用2。4g无线rf传输技术,发射功率0db,接收灵敏度-98db

the rf is standardwith2.4gism,the tx power is 0dband the rx sensitivity is -98db.

2

具有64个跳频频道,每个频道间隔1mhz

the rf has 64 channels,the channel gap is 1mhz

3

空旷直线传输距离大于15米

the transmission distance is further than 15 meters with nobarrier

4

智能无线技术,实现自动跳频,自动节约功耗,自动id码学习

the protocol designed with high performance

5

采用跳频传输,抗干扰能力强;能自动避开无线路由器,2。4g无线耳机,蓝牙设备的干扰。

to jump frequency adaptively when noised ,which can work with2.4g wireless mic ,wlan and bluetooth etc. devices.

6

跳频传输技术,同一个房间,能支持32套设备,同时使用,相互不受影响

32 setswirelesshandlework fine at the same time in one room ,withno-interference each other

备注:不使用对刀器的时候,建议将对刀器电源按钮拨动到关的位置,以节约电池用电。

打开电源开关,工作指示灯不亮的情况下,不要使用对刀仪,防止刀具压坏仪器。

无线对刀器采用3v纽扣锂电池工作,当低压指示灯亮的时候,表示电池电量快用完了,建议更换电池。

note:when not in use when theinstrument,proposed to instrument the powerbutton toggle to the off position to conserve batterypower.

turnthe power switch, the working indicator does not light thecircumstances, do not use the e, crushing e toprevent the machine

the heightsetting instruments work with 3v lithium coin;when the low pressure indicatorlight when the battery is running out, the proposed replacementbattery

六.使用功能描述(featuresdescription)

对刀器指示灯

名称

功能描述

工作状态指示灯

workingstatus indicator

当把对刀器电源开关打开;

如果对刀器工作正常:该指示灯常亮;该指示灯灭,则对刀器工作不正常,建议先排除故障,再使用

工作指示灯不亮:检查对刀器接收器是否安装在电脑上

对刀器工作正常,必须要保证工作指示灯常亮

open theinstrument power switch if the instrument is working properly:always lights work; work lights off, the instrument is not workingproperly, it is recommended troubleshooting, re-use

light does notwork: check the receiver is installed on your computer

告警指示

alarmindication

在工作状态下,当机床对刀操作的时候,机床刀具压下对刀器探头往下移动,达到设定的高度情况下,告警灯常亮,对刀器的接收器将停止机床移动。

如果机床还继续移动,停不下来,则该灯闪烁,提示用户,需要手动停止机床。

inworking condition, when the machine tool under pressure apparatustantou wang moved to the location of the tool height
when the warning lights lit, forcing the machine to stop movinge

ifthemachinecontinues to move, not stop, the lights flash, prompting the userneeds to manually stop the machine

低电压指示

lowoltageindication

当电池电量不够的时候,该灯常亮,提示用户更换电池。

when thebattery isnotenoughtime,thelightslit,promptsthe user toreplace thebattery.

电源开关

powerswitch

当把电源开关拨动到on的位置,打开对刀器,如果对刀器接收器连接在电脑上,则对刀器工作指示灯亮。

当把电源开关拨动到off位置,则关闭对刀器电源。

平时,不使用对刀器的时候,建议关闭对刀器电源。

whenthe power switch to toggle to the on position, open the instrument,if the receiver connected to your computer, then the indicatorlight instrumentation

whenthe power switch to toggle to the off position, turn off theinstrument power.

when notusing the instrument, the proposed power off theinstrument.

成都新宏畅无线科技有限公司

www.xhctech.com

展开全文
我们其他产品
相关产品
无线会议系统 无线监控系统 货架供应 食品供应商 柴油供应商 供应钢材 供应不锈钢 柴油供应 供应信息 中国供应商 超市供应商 供应废塑料 蔬菜供应 IC供应商 牛肉供应商
在线询价 拨打电话